View Profile: Engenia - Benelli Motorcycle Forum

Today, 06:13 AM

Engenia replied to a thread Lithium battery. in Tornado Tre

Couldn't help myself Tony. I'm an engineer. It's hard to argue against science, but people keep trying.

9 replies | 159 view(s)

08-18-2019, 05:03 PM

Engenia replied to a thread Lithium battery. in Tornado Tre

The alternator is capable of 48A so I don't see any reason why you would want to limit an external charger. Balancing should be taken care of inside...

9 replies | 159 view(s)

08-16-2019, 06:14 PM

Engenia replied to a thread Tornado tre 900 04 plate in Classifieds-For Sale/Wanted

Best you leave the fold then.

7 replies | 268 view(s)

08-11-2019, 05:45 PM

Engenia replied to a thread Jersey TNT in General Benelli Discussion

:rolling:When I see posts like this Laurence, I always think of Big Bad Al's famous Gixer post:rolling: (It wasn't me btw.)

4 replies | 101 view(s)

08-11-2019, 07:54 AM

Engenia replied to a thread OEM replacement foam filter vector drawings in Benelli Technical

The DWG link in the first post is now to the Rev 1 drawing. It contains three layers. One is the scanned & vectorised support (light blue), another...

3 replies | 118 view(s)

08-08-2019, 05:13 PM

Engenia replied to a thread Cafe Racer not starting in TNT

No idea. I've never had one apart. Let us know what you find.

19 replies | 432 view(s)

08-08-2019, 06:54 AM

Engenia replied to a thread Cafe Racer not starting in TNT

You wouldn't have, unless you have also seen the fuel pump. It's right next to it. It's simply a valve and a spring. Perhaps 10 mm diameter

19 replies | 432 view(s)

08-07-2019, 06:01 PM

Engenia replied to a thread Cafe racer questions in TNT

Not caused by tolerance in the starter gears, although the 1130 benefits from a higher ratio than the 900s. It's the alternator drive shaft / Z25...

4 replies | 143 view(s)

08-07-2019, 05:46 PM

Engenia replied to a thread Cafe Racer not starting in TNT

Either the fuel pump or the bypass valve - which regulates the pressure.

19 replies | 432 view(s)

08-07-2019, 04:39 AM

Engenia replied to a thread Anyone Know what this marking is in Tornado Tre

I think its the engine number, but I can't read it as it's out of focus. Nothing to do with mods though

10 replies | 248 view(s)

08-06-2019, 05:25 PM

Engenia replied to a thread Cafe Racer not starting in TNT

Not necessarily. If it is too lean you'l get nothing. For instance, if the AFR at normal starting is 11:1, halving the pressure will change the AFR...

19 replies | 432 view(s)

08-05-2019, 06:51 AM

Engenia replied to a thread Cam chain tensioner not moving in 20000 km. Is that normal? in TNT

Measure it over 35 links. I do it on a scanner with a ruler, compressing the chain for one shot and elongating in another. Then I use GIMP to move...

20 replies | 1943 view(s)

08-01-2019, 05:13 PM

Engenia replied to a thread Fuel tank in Tornado Tre

You need to push it all the way in. When the tool is below the fuel hose level, that'll be it. Then push the hose in a little before removing it.

3 replies | 116 view(s)

07-30-2019, 06:00 PM

Engenia replied to a thread Basically a goldwing ! in Tornado Tre

Be careful how you put a load onto the tail fairing. Do it wrong and you will break both top mounting points

4 replies | 148 view(s)

07-30-2019, 05:53 PM

Engenia replied to a thread Concerned almost new owner in Benelli Technical

It's not uncommon for manufacturers to set the VIN incorrectly, the check digit in particular. Manufacturer: BN - Benelli Model specific: TB000 -...

2 replies | 106 view(s)

07-30-2019, 06:48 AM

Engenia replied to a thread Mudguard required in Tornado Tre

If you can't find a 2nd hand one you might look into a carbon fibre one. I know someone's done it 'cos I've got one on the shelf. Try Carbon SK 2nd...

3 replies | 90 view(s)

07-30-2019, 06:35 AM

Engenia replied to a thread 1130 Power Commander in TNT

Looks like you've already go one. Oh, crap! That would be you :doh: Seriously though, you don't need it. Benelli haven't locked you out of the...

43 replies | 5146 view(s)

07-29-2019, 04:55 PM

Engenia replied to a thread Z25 Gear and Shaft Replacement in Benelli Technical

From my site everything you ever wanted to know about it. BTW. the latest shaft / gear don't have alignment marks. I assume that the gear is made...

94 replies | 28592 view(s)

07-28-2019, 11:50 PM

Engenia replied to a thread OEM replacement foam filter vector drawings in Benelli Technical

I received the foam filter from Unifilter today and its a deal better than the OEM, in that it seals at the edges more positively. It could have done...

3 replies | 118 view(s)

07-28-2019, 04:23 AM

Engenia replied to a thread TNT gearbox in Benelli Technical

Isn't that defined by the selector forks? In the Tornado the fork slot play is < 0.5 mm. Of course the fork pin could be worn and there's no spec...

1 replies | 74 view(s)

07-27-2019, 06:47 AM

Engenia replied to a thread Z25 Gear and Shaft Replacement in Benelli Technical

I have no record of it, but not everyone sent me their upgrade details for inclusion on the webpage

94 replies | 28592 view(s)