View Profile: Rick67 - Benelli Motorcycle Forum - Benelli Bike Discussions
Benelli Motorcycle Forum - Benelli Bike Discussions - Powered by vBulletin
Tab Content
  • Rick67's Avatar
    06-20-2019, 03:41 PM
    Fantastic .. looks awesome and a real credit to you .! . Mines currently getting a tuning around the roads of Europe too(sporting its carbon parts...
    5 replies | 78 view(s)
  • Rick67's Avatar
    06-15-2019, 08:50 AM
    Somewhere In France ...Mont-Saint Éloi apparently.
    3 replies | 100 view(s)
  • Rick67's Avatar
    06-13-2019, 03:52 PM
    Rick67 replied to a thread TNT 899S front fairing in TNT
    Have Garry ... It may be hidden in the same place as my Trek . If it is it'll be up behind very front of the peak of the headlight fairing ,...
    3 replies | 72 view(s)
  • Rick67's Avatar
    06-13-2019, 03:31 PM
    Rick67 replied to a thread Headlight issues in Tornado Tre
    i second this question :clap:
    9 replies | 225 view(s)
  • Rick67's Avatar
    06-12-2019, 03:49 PM
    Rick67 replied to a thread Balls in TreK
    Oh shit ....Not seen on in mine ... Double balls !
    1 replies | 65 view(s)
  • Rick67's Avatar
    06-11-2019, 08:58 AM
    Rick67 replied to a thread Tps in Benelli Technical
    That's possible I guess ..mine had a dead spot at where the 5% throttle position would of been , my bike ran a bit rough in that area until I...
    5 replies | 94 view(s)
  • Rick67's Avatar
    06-11-2019, 01:13 AM
    What a daft Apeth... The only mistakes I take nowadays are taking too much crap with me ... Not this time. Loaded Stuff sack half filled top box...
    3 replies | 100 view(s)
  • Rick67's Avatar
    06-11-2019, 12:14 AM
    Hi all... I'll be making my way to the Black Forest area near Freiburg this Saturday the 15th for the week . Leaving the UK at 12 pm ish from...
    3 replies | 100 view(s)
  • Rick67's Avatar
    06-10-2019, 03:51 PM
    I'd be looking under the relay bank to make sure there's no loose wires ect.. It is known that the connections to all the relays can go slack over...
    6 replies | 159 view(s)
  • Rick67's Avatar
    06-10-2019, 03:41 PM
    Rick67 replied to a thread side stand in TreK
    Hi Ron it is the steel stand I had to re paint after its alteration .. it gets some stick down here with the gravely roads and my light off roading...
    9 replies | 177 view(s)
  • Rick67's Avatar
    06-10-2019, 11:08 AM
    Rick67 replied to a thread side stand in TreK
    Hmm .. mine was fine as it was until the bolt snapped lol... Angus to the rescue on that bit. I then lowered my bike as a test and had to lower the...
    9 replies | 177 view(s)
  • Rick67's Avatar
    06-08-2019, 02:22 PM
    Well.... It's Looks pretty but does it work ? .... 😉
    6 replies | 159 view(s)
  • Rick67's Avatar
    06-05-2019, 01:03 PM
    Hi Glynn . On Amazon UK.. just type valve shims ( not being funny honest ) 🙂. I guess best thing to do is get yours appart to measure...
    14 replies | 236 view(s)
  • Rick67's Avatar
    06-05-2019, 11:56 AM
    I may of seen a post stating 8mm in diameter. Don't quote though . You can buy kits with a massive selection for about £30
    14 replies | 236 view(s)
  • Rick67's Avatar
    06-03-2019, 08:18 AM
    Rick67 replied to a thread valve clearances in TreK
    All I know is that my valve clearances are still smack in the centre of tolerance for inlet and exhaust after a rebuild of my engine over 13,000...
    5 replies | 656 view(s)
  • Rick67's Avatar
    06-03-2019, 08:12 AM
    It's more likely to be that the spring doesn't suit your weight . If the damping is working ok just get a new spring for your weight and set the...
    4 replies | 93 view(s)
  • Rick67's Avatar
    06-01-2019, 10:03 AM
    I have just had the same thing with mine .. it was going through all the positions from 1% to 100% but skipped 5% every time . So id already cleaned...
    10 replies | 178 view(s)
  • Rick67's Avatar
    05-31-2019, 03:49 PM
    I've read a post from a few years back from Lawrence saying he found his was the o ring near the bearing on the dry clutch ... Does that ring a bell...
    5 replies | 117 view(s)
  • Rick67's Avatar
    05-31-2019, 12:11 PM
    Rick67 replied to a thread Cutting out in TreK
    Haha.... I bet you've emptied your outbox though 😉
    19 replies | 376 view(s)
  • Rick67's Avatar
    05-31-2019, 11:30 AM
    Rick67 replied to a thread Cutting out in TreK
    Check your inbox ..
    19 replies | 376 view(s)
  • Rick67's Avatar
    05-29-2019, 04:45 PM
    ill be pinching that !!:ele::ele::ele::bow:
    6 replies | 196 view(s)
  • Rick67's Avatar
    05-29-2019, 04:40 PM
    Rick67 replied to a thread Tnt 1130 2006 in TNT
    hi maybe your stepper motor just needs a clean especially if its only trouble starting a cold engine. i see you have had the bike running in your...
    8 replies | 348 view(s)
  • Rick67's Avatar
    05-29-2019, 04:11 PM
    Rick67 replied to a thread New luggage and lights in TreK
    you've done a good job on them Ron, im sure you'll get them to work as you want to in the end :clap:
    8 replies | 149 view(s)
No More Results
About Rick67

Basic Information

About Rick67
Name:
Rick
Location:
Brynamman ,Wales

Statistics


Total Posts
Total Posts
407
Posts Per Day
0.62
Albums
Total Albums
1
Total Photos
1
General Information
Last Activity
Yesterday 11:48 PM
Join Date
09-04-2017
Referrals
0
Google+